Duct Detector Sampling Tube (1500-3000mm duct width)
Sampling Tube for duct smoke detectors.
Duct Detector Housing (XPERT 7)
The Duct Detector Housing provides early detection of smoke in the air moving through heating and ventilation (HVAC) ducts in commercial and industrial premises. Its purpose is to prevent the re-circulation of smoke from an area on fire to areas unaffected by the fire when used with a XP95 or Discovery detector.
XP95 Flame Detector (UV/IR2) – Base Mounted
The XP95 Flame Detector (UV/IR2) is designed to protect open indoor areas such as aircraft houses, generator rooms and paint works where open flaming fires may be expected. The detector has a UV and dual IR sensors responding to different wavelengths in order to discriminate between flames and spurious sources of radiation. Responds to stationary […]
XP95 Flame Detector (UV) – Base Mounted
The XP95 Flame Detector (UV) is designed to protect enclosed indoor areas where open fires may be expected. The detector has a fast acting response to flames up to 25m away and is equipped with a single UV sensor with a narrow spectral response in order to discriminate between flames and most spurious sources of […]
XP95 Flame Detector (IR3) – Base Mounted
The XP95 Flame Detector (IR3) is designed to protect all indoor areas, even in dirty or smoky conditions where open flaming fires may be expected. The detector has three IR sensors that respond to different IR wavelengths in order to discriminate between flames and spurious sources of radiation. Responds to stationary flames with no flicker […]
XP95 Flame Detector (IR3)
The XP95 Flame Detector (IR3) is designed to protect areas where open flaming fires may be expected. It is sensitive to low frequency, flickering infra-red radiation emitted by flames during combustion. Loop-powered Sensitive to flickering IR radiation Detects through films of oil, dust, water and ice Responds to flickering flames, including those invisible to the […]
XP95 Flame Detector (IR2)
The XP95 Flame Detector (IR2) is designed for use in areas where flaming fires may be expected. The detector has two sensors which respond to different IR wavelengths to discriminate between flames and spurious sources of radiation. Sensitive to flickering IR radiation Detects through films of oil, dust, water and ice Responds to flickering flames, […]
Flame Detector Weather Shield
The Flame Detector Weather Shield protects the device from inclement conditions. Protects against water ingress Protects sensor from direct sunlight
Flame Detector Bracket
The Flame Detector Bracket is an optional accessory for the Intelligent Flame Detectors. It is a stainless steel mounting bracket adjustable in two axis. Not suitable for Base Mounted Flame Detectors. Allows flame detector to be mounted in any orientation.
Exd Flame Detector Weather Shield
The Flame Detector Weather Shield protects the device from inclement conditions. Protects against water ingress Protects sensor from direct sunlight
XP95 Reflective Beam Detector (5-50m)
The XP95 Reflective Beam Detector differs from a traditional beam detector in that it is a single unit which houses a transmitter, a receiver and the control electronics. Loop-powered Compatible with Discovery and XP95 protocols Incorporates a short-circuit isolator Automatic drift compensation Automatic reset following alarm or fault condition
Reflective Beam Detector Head (Add-on) – Auto-Aligning
Additional Head for the Auto-Aligning Beam Detector.
Intelligent Reflective Beam Detector – Auto-Aligning
The Intelligent Auto-Aligning Beam Detectors use the light obscuration principle and sees light produced by the transmitter. Beam detectors are ideal to monitor large open areas and buildings with high ceilings. EN 54-12 & EN 54-18 Certified Allows use of 2 detector heads per low level controller Each detector head configurable from 8m to 100m […]
Beam Detector Surface Mounting Plate
Surface Mounting Plate for Auto-Aligning Beam Detector.
Beam Detector Prism Plate (4 prisms)
Mounting Plate (4 Prisms).